知識業內對兩個產品的叫法不一樣，說是鰭片管的可能是從事這個行業比較久一點的人員，實質東西和結構沒有太大區別。一般鋼質的都是在無縫鋼管上焊接而成。普遍認為螺旋鰭片管中的鰭片高度要比螺旋翅片管中的翅片要高一些（這個不是主要因素，翅片高度都是可以按客戶要求定制的）。不過螺旋鰭片管相對的螺旋翅片管來說使用的環境比較惡劣，焊接工藝相對要嚴謹一些。話雖如此只是新產品整體型鋼質螺旋翅片管大家還沒有認識或者見識到，目前市場上基本都是理解成一個產品，只是需要從業人員知道就好了，便于服務客戶。The term for the two products is different in the knowledge industry. It is said that the fin tube may be a person who has been engaged in the industry for a long time. The substance and structure are not very different. Ordinary steel is welded on seamless steel pipe. It is generally believed that the fin height in the spiral fin tube is higher than that in the spiral fin tube (this is not the main factor, fin height can be customized according to customer requirements). However, the spiral finned tube relative to the spiral finned tube for the use of the harsh environment, the welding process is relatively rigorous. That said, it is only a new product of integral steel spiral finned tube we have not yet known or seen, the current market is basically understood as a product, but the need for employees to know it, easy to serve customers.螺旋鰭片管和螺旋翅片管什么區別What is the difference between spiral finned tube and spiral finned tube?鰭片管和翅片管的主要作用就是增加受熱面（或散熱）、提高傳熱效率。The main function of finned tube and finned tube is to increase heating surface (or heat dissipation) and improve heat transfer efficiency.焊接強度和穩定性區別Difference between welding strength and stability1.1 拉脫力試驗: 大于200MPa 或者鋼管部分撕裂1.1 pull-out test: greater than 200MPa or partial tear of steel pipe.1.2焊縫寬度: 大于翅片厚度 即焊著率>99%1.3焊接強度穩定性: 每班首件做焊接試樣 達到2.1 或者2.2的要求1.2 Weld Width: Thicker than Fin, i.e. Welding Rate > 99% 1.3 Welding Strength Stability: The first part of each shift to do welding specimens to meet the requirements of 2.1 or 2.21.4 焊縫抗彎曲試驗: 翅片左右彎曲20度 向左向右彎曲兩次 焊縫無裂紋1.4 weld bending test: fins bending about 20 degrees to left to right bend two times weld without crack.1.5 錘擊試驗: 平行于鋼管敲擊翅片上部 直到翅片脫落 翅片本身不得斷裂1.5 hammer test: parallel to the top of the steel pipe beating the fins until the fins are detached, and the fins themselves must not be broken.1.6 如果試驗失敗 必須啟用退火功能1.6 if the test fails, the annealing function must be enabled.熱影響區區別Heat affected zone difference用顯微鏡配合微硬度計測量Measurement with microscope and micro hardness tester鋼管熱影響區深度小于0.5mmThe depth of heat affected zone of steel tube is less than 0.5mm產品尺寸精度區別Product size accuracy difference3.1 翅片段全長 -1mm ~ +1mm 分段運動精度 -0.5mm ~ +0.5mm3.1 wing segment full-length -1mm ~ +1mm segmented motion accuracy -0.5mm ~ +0.5mm3.2 片距 -0.2mm ~ +0.2mm3.2 slice distance -0.2mm ~ +0.2mm3.3 翅片和鋼管垂直度 -1度 ~ +1度3.3 fin and steel tube perpendicularity -1 ~ +1 degrees3.4 同組對焊翅片平面度 -0.2mm ~ +0.2mm翅片本身厚度公差引起的高度差除外3.4 the same group of welding fins flatness -0.2mm ~ +0.2mm fin thickness tolerance caused by height difference except.3.5 同組對焊翅片高度差 -0.2mm ~ +0.2mm 翅片本身尺寸公差引起的高度差除外3.5 the height difference of the welding fin is the same as that of the -0.2mm group, except for the height difference caused by the size tolerance of the fin +0.2mm.3.6 雙管中心距離公差 -0.5mm ~ +0.5mm3.6 double center distance tolerance -0.5mm ~ +0.5mm3.7在同樣鋼管材料, 同樣片距和片數條件下, 不同翅片管焊接后長度變化一致3.7 under the same steel tube material, the length of the finned tubes will be changed after welding with the same chip spacing and number of sheets.焊接速度區別Difference of welding speed基管外徑25~51 翅片厚度2mm 每對焊接時間小于3秒 (不包括上下料時間和退火時間)Welding time of each pair of fins with 25-51 outer diameter and 2 mm thickness is less than 3 seconds (excluding loading and unloading time and annealing time) 方管